1911Forum banner

1 - 20 of 27 Posts

·
Registered
Joined
·
25 Posts
Discussion Starter #1
For those that have used Caspian frames and slides, how difficult would it be for someone to make a working firearm?

What is the investment in parts, tools, etc.?

I would love to build a gun from scratch, but is this something a non-gunsmith could accomplish?

Thank you!
 

·
Registered
Joined
·
1,225 Posts
I think you want to share how skilled you are with your hands, especially with metal files and measurement tools. It can be done with have tools, and not a huge investment in specialty tools, but it is NOT the same as building are AR15. Please expand on your background.
 

·
Registered
Joined
·
6,389 Posts
Get the Jerry Kuhnhausen 1911 Shop Manual. Read it until it is as familiar as your route to "Grandma's"!

http://www.yourperfecthomengarden.com/kuhnhausen-1911-shop-manual.pdf

Report back in 24 months!

All the best,
 

·
Registered
Joined
·
126 Posts
I'll second what John and Hop said.

It also might help if you told us your end goal.

Do you want to make a gun that has all the features you want and looks just the way you want it to? That's certainly within the realm of hand tool building. That said, I'd advise you not to expect it to cost less than the least expensive commercial guns, or to be worth a fortune if you ever decide to sell it. The reward of building your own 1911 is rarely financial. What you'll be getting is the gun you build, and a gun you know you built when you take it to the range. That can be worth a lot to those of us who enjoy building 1911s.

Do you want to make a gun that will hold the X-ring at 50 yards using only hand tools? That's possible as well, although getting there involves a different level of puzzle solving. Again, building a gun that can hold its own with the best can feel amazingly rewarding.

And any way you choose to tackle it, building your first 1911 will be an exercise in puzzle solving--no matter how many tools you already have. I loved doing my first Caspian build for that reason alone. I learned a ton of stuff about the platform that I'd only had reading knowledge of before. And that, in turn, gave me a new respect for the builders on this forum who've truly mastered the art.

If you like figuring out and understanding mechanical puzzles, you'll be in for a treat.

Hope that helps,

David
 

·
Registered
Joined
·
466 Posts
^^ what these gents said ...

It's not hard, but it does take time. Starting with frame that has all the basic machining done (as opposed to 80%) makes it much easier. It's then more a matter of detail fitting than outright machining.

It does help to have a good basic set of mechanical skills and skill with files.

I find that my own builds are what I typically take to the range, I guess in part due to the gun having been made with the features I wanted. It's also fun to respond to people who ask what brand of 1911 I'm shooting with "mine." This often leads to some humorous dialog of "yes, I know it's your pistol, but who made it .... ?"
 

·
Registered
Joined
·
6,524 Posts
It is hard to do it right unless you have a certain skill set. You also need to understand how the system works (Kuhnhausen seems to be the go-to source). Since you mention Caspian I'll go with that in mind, and assume that you are going to want the same quality in the other parts to complete the project. You are looking at somewhere in the neighborhood of $1300 for part, including too much of the tricks that one can have done to make a gun pretty. Add is a couple of hundred for basic tools. This does not include any machining if you go with a ramped barrel, want some sort of treatment to the front strap. If you have not done this before you probably ought to order and extra thumb safety, you will almost assuredly botch the first one. I have factored into the $1300 a beadblasing of stainless, if you want any other finish, add that figure in. As you can see you are now in the Les Baer, Dan Wesson range, with no guarantee that it will run reliably or be accurate. But you will have built a gun and you will know how the 1911 system works. You could go with cheaper parts and then you won't really know if the problem is you or the cheap parts.

I would also say that you might want to pick up something like Springfield Mil Spec, make sure it functions by shooting a few hundred round through it. Then do the work one piece at a time, after each re-test fire. If you get a failure, at least you now know where the problem is and what to look at.
 

·
Registered
Joined
·
157 Posts
Absolutely agree with everyone above.

Read each suggestion carefully a couple times.

Starting with a serial numbered lower receiver and a matched slide and barrel will teach you TONS about practical gunsmithing and very likely re-inforce (or introduce) your respect for the sheer engineering genius that was John Moses Browning.

When Para first made their wide body aluminum frame available, I started a build immediately. And even switching parts off of a brand new Springfield MilSpec presented challenges. I learned that I will personally NEVER attempt to do the hammer/trigger/sear work ever again - while throating the barrel and other things were very straight forward. (I probably did 20+ 1911s to feed Speer Flying Ashtrays)

Files. Stones. A Dremel if you feel really confident, because there's no putting material back onto a frame or slide or barrel once you take it off.

What you intend to do with the finished product does bear some thought - but again, carefully consider the posts above. Sights, safeties, barrels, finish - all will impact your work.

I recommend Major George Nonte's book "Gunsmithing" be on your shelf. It's a bit dated, but it was one of the very first sources for caliber conversions and radical customizations of the 1911 - like what would become the production Detonics. There are lots of other superb books.

Now, to complicate, not simplify the discussion...

You can start with an 80% lower, and if you don't mind aluminum, the job of finishing out a 1911 lower in aluminum can be done fairly easily now with an investment in a Ghost Gunner II. Roughly $1700 plus shipping, plus an 80% aluminum lower - another $150? Bolt up the lower with the right jig bits, let the machine auto-sense the lower, and sit down. After a while the Ghost Gunner will hand you back a 100% ready lower. (And it can do AR15, AR10 and Glock as well now, since the control files are written).

I do not own one, and am only suggesting the above because the technology does exist to complete an 80% without hand tooling it. There are also jigs and fixtures available from Stealth and Matrix that would help do the same thing as manual and labor intensive.

Why does this complicate? Cutting slide rails, drilling holes that have to be in precise places or the trigger/hammer/sear geometry is not right are "advanced course work".

And if you finish out an 80%, an additional level of complexity, because once you make a firearm for yourself, it is yours. No selling it (unless you get a Class 07 SOT License, maybe?) Anyway, if you decide to do the 80% route, please become completely familiar with the ATF rules.

So, reduce complexity and cost. Decide on your basic goal - target, carry, etc. Then get a good quality Caspian lower and slide and barrel with the surety that they put all the holes in the right places, carefully collect knowledge and parts, and enjoy both the journey, and the destination!
 

·
Registered
Joined
·
137 Posts
I have built 6. 4 in 9mm and 2 in .45acp. .45 is a whole lot easier to get it to function properly. I did my own Cerakote and time invested on each was around 40 to 60 hours depending on the frame/slide manufacturer and learning curve of previous builds. The cost ranged from around $1800 to one Caspian double stack that I sent in to Nighthawk to have some milling that I don't have the tools for and hard chrome. That one with 4 mbx mags and RMR sight set me back close to 4k.

I personally don't think it is worth it if you are only going to build 1. Take the 2k and the other $500 or so for tools and by an Ed Brown, or used Nighthawk or Wilson. They will be worth more one the resale market than you will ever get for the one you build.
 

·
Premium Member
Joined
·
8,358 Posts
I have built several. When starting out there is something to be said for starting with a working GI configuration pistol. Choose a RIA (or Phillipino derivant), SA MilSpec, a Turkish make. Shoot it, determine what you want to improve. Do the modifications one at a time. Shoot is some more to see if it ‘works’ for you. It magically becomes YOUR pistol at half the cost. Additionally, if something doesn’t work with the modification you will know the fault will lay in modification performed, not in something else affecting the fitting performed.
Once you have that experience under your belt a time or two try a ground up build. Caspian and the other name makers build good components, any error at that point will typically be on you.
As mentioned in previous posts, staying with a good completed, serial numbered frame is the most feasable start should you go the ground up approach.
 

·
Registered
Joined
·
130 Posts
For those that have used Caspian frames and slides, how difficult would it be for someone to make a working firearm?

What is the investment in parts, tools, etc.?

I would love to build a gun from scratch, but is this something a non-gunsmith could accomplish?

Thank you!
Yes, someone who has never made a 1911 can build a functioning firearm or 1911. I did. With no supervision or previous experience and a butt load of tools that you've never used before, it can be done. If you're going to buy a Caspian frame and slide, and you want parts of at least equal quality, you're looking at around $2,000 for a standard 1911 with a mix of Wilson Combat, Ed Brow, EGW, Harrison Custom, and Wolff, plus tools. It's easy to spend another $700-$1500 on tools specific for building and finishing a 1911 if you don't already have at least some of them.

A friend of mine recently bought a parts kit with a frame from E-Sarco and made a functioning 1911. It's worth your time to compare the costs.

If you want to go the route of making from an 80% frame, you'll be buying or borrowing even more specialized tools. For example, a slot cutter tool for the frame. What else can you use that for? Nothing. A barrel seat cutter tool. What else can you do with that? Nothing. In my experience, I ended up buying as much specialized tools and had more guess work and doubts going the 80% route. I think I even ruined five safety levers before I got it right, and it turned out that the stacking tolerances added up to be root cause of it. Ultimately, my sear was cut beyond spec.:grumble: Don't let any of that discourage you. I learned a lot. Although, if I had to do it all over again, I'd start with parts and a 100% frame.
 

·
Registered
Joined
·
7 Posts
If you have lots of time and lots of money, then....it's really difficult. I built one from scratch in 2004 I have a machine shop building hi-perf motors so what the hey, totally different, by the time I was done buying the special tools and the hours of hand fitting parts, (and yes Kuhnhausen manual was needed) I got a great gun, still my favorite 1911 to date, but if I charged $5 an hour for the labor this gun would have cost about $10000.
Herego the old statement "you can't beat a good man at his trade"
Just my 2 cents worth.
Happy shootin' JD
 

·
Registered
Joined
·
93 Posts
I have to pretty much agree with the previous comments. I've built only one. I started with a serial numbered frame and a slide already cut for my sights. Then I spent a while with the Brownell's catalog ordering all the small parts. One short cut was using a matched trigger set from C&S. I definitely agree; buy quality parts. I had tried inexpensive (read here cheap) ones earlier and they were more difficult to fit and didn't really blend well.

All told, I had about $1300 in parts, probably another couple of hundred in tools before I was done. And JD is right, the labor charge is NOT included.

Sure I could have bought a nice one for that, but it wouldn't have been "mine".
 

·
Registered
Joined
·
395 Posts
My first and only build was a Heinz 57. Essex frame, Colt commercial slide, Sig 1911 barrel and a mixture of Wilson, Brown and Cylinder & Slide parts. I had a gunsmith mill the slide for sights and refinish. It was a learning experience and I had luck with me. I won’t do it again because it ended up being more expensive than a nice new 1911 from Sig, Colt, Kimber, you name it.
 

·
Registered
Joined
·
639 Posts
My first "build" was to buy a stainless Caspian frame with a checkered front strap, then to fit a stainless S&W E series slide to the frame. I also fit a full set of fire control parts, a new thumb safety, and an upswept grip safety into the Caspian frame. To fit the slide I used a stoning jig from Everglade Ammo. Once I got the slide fit to the frame, the rest went together with only minor fitting. I used all quality parts and had no problems getting a nice functioning pistol.
My next build was an aluminum officers frame from Caspian. The slide / barrel assembly used was a carbon steel Colt Combat Commander in .38 Super. With this build I used fire control parts from Cylinder & Slide, a Wilson Combat Bulletproof thumb safety, a .250 radius grip safety from S&A, and a Wilson Combat rounded mainspring housing. I again used the Everglades stoning jig to fit the slide, then assembled the pistol, again with minimum fitting. Once I had the pistol up and running, I sent it to my gunsmith for him to send it to his anodizing shop, and to mill the frame for a polished steel feed ramp. I'm still waiting for the competed pistol to return from anodizing. My investment in this .38 Super CCO will be near $1500.00 when finished.
 

·
Registered
Joined
·
979 Posts
Before I would spend the money on a first time custom build, I would go the route of an experience build.
Get a parts kit from Sarco and a frame. It will not be much when you finish but it will give you a lot of experience. You will mess up some parts but at least they will be cheap to replace.
It will be functional and give you a lot of experience before you spend the big bucks. Plus it should answer your question"How hard is it to build a 1911?"
 

·
Registered
Joined
·
6,524 Posts
There is a difference between building a gun and putting one together. Many people can put one together and it functions (at least for a good while). If you read the stuff some of the smiths write here on correcting guns that don't seem to function reliably, things like VIS, ramp angles, the fine point of tuning an extractor, the art of a trigger job that lasts the lifetime of the gun. Not many can do that sort of build without years of learning. With that said it is the best way to learn how a 1911 works and how to diagnose issues. DON"T buy a Sarco, get good parts it is much easier and they are much more likely to be in spec. The other option is to get a lower cost working gun (Mil Spec) and one part at a time make your changes. After each change make sure it works and then move on.
 

·
Registered
Joined
·
1,694 Posts
For those that have used Caspian frames and slides, how difficult would it be for someone to make a working firearm?

What is the investment in parts, tools, etc.?

I would love to build a gun from scratch, but is this something a non-gunsmith could accomplish?

Thank you!
Don't jump in the deep end, start easy and advance as your skills advance.

My recommendation would be to start with a "lego" 1911; something that doesn't require fitting of the frame and slide. I would also steer toward "drop in" parts.

Get all drop in stuff, build the pistol and then learn the in's & out's of fitting each part as you slowly improve the pistol you build. I would recommend starting with all stainless as you can build, and then make changes as you see fit without having to refinish the pistol.

Also, skip the Kunhausen book; it sucks. I can't recall learning ANYTHING from that book, and everyone talks about it like it's holy scripture. If you want a book, find something better (although I don't have any recommendation that is more up to date than Layne Simpson's or Bill Wilson's old books).

Watch Youtube video's. Watch a good 3-4 videos for each step and each part. That way you see it from different angles, and from different pistolsmiths...And you have a higher chance of weeding through the bad videos and finding the really good ones; and there are some very good ones out there.

ETA - If you start simple, you're much more likely to be successful, and that's gratifying. If you try to build a really high end custom pistol, there's a good chance you'll fail, and probably ruin some parts along the way. Even if you can afford that, still a bad and potentially demoralizing reasons to not try that first.

But DO the build, you won't regret it. Once you get the knack, working on 1911's is a LOT of fun.
 

·
Super Moderator
EDC: SIG P938.
Joined
·
22,145 Posts
I never had so much as a high school metal shop class, and I've done some building.
If there had been something seriously wrong with the parts, I may not have been able to determine what it was (breechface or feedramp at wrong angle, mislocated holes, etc.), but I was able to do all the necessary hand-fitting of quality parts without much trouble.
I did install parts on functional guns as a start, then graduated to buying the parts necessary to build a complete gun.
Highly recommend Hallock's .45 Handbook, if you can find it, and Kuhnhausen.
 
1 - 20 of 27 Posts
Top